Linksys X3000

del

О, да тут прямо клуб любителей P660HTW2
Самого вот мучает вопрос как бы поиметь гигабитный свич. Начал зондировать тему, и сразу попал сюда. Господа, а есть еще достойные альтернативы? Дороговатый то девайс получается Или я не прав?

Netgear DGND3700, но он стоит еще дороже.

Кто пользовался X3000 и юзал торренты и интернет.
Нормально ли работает, не зависает ? На какой прошивке ?

Lord Havoc:

Кто пользовался X3000 и юзал торренты и интернет.
Нормально ли работает, не зависает ? На какой прошивке ?

Работает нормально, не зависает, прошивка любая.

То же интересует как wi/fi работает

SJS-FCB:

Да, тоже приметил. Но действительно дороже. Видимо альтернатив в сегменте "ок.150уе" вообще нет.

А как же NETGEAR DGN3500?

А какая у вас скорость чтения/записи на ЮСБ диск подключенный к гаджету? Че-то меня мой совсем не порадовал, до 5тый. кбайт/с в Тотале, не выше.

Такая же проблема:после прошивки Ver.1.0.04 интернета НЕТ.
Как только его не настраивал результата нет.
Вернул Ver.1.0.03 - курит в лучшем виде!

how to recover from failed upgrade of Linksys X3000

I have seen a similar topic in earlier posts, but it did not have a solution.
I would like to share my experience of fixing the problem.
My device is Linksys X3000 modem\router
What happened: I `ve tried to upgrade my router over Wifi connection and it failed
when the progress was at 98%. Obviously I should not have done it over the WiFi.
There wasn`t any warning when I`ve done that...
When I got to this situation, my modem has had only power LED on and it was shining red.
I have tried using reset button(including 30sec-30sec-30sec method), but it did not recover the modem itself(as
I later found out, it did reset the config only).

But thanks a lot to a support over a live chat. They are tremendously helpful - I have never seen a better support.
No stupid questions! Its amazing.

With their help the following method of recover worked for me:
- connect PC to the modem using wired ethernet connection
- if the IP address is not automatically assigned(i.e. DHCP server is down on the router), then
assign it statically on the PC. This is a key moment. The subnet you should depends on whether
the config was already reset by this time. If it was, then use the default network settings.
It should be 192.168.1.x subnet. The modem should have 192.168.1.1, you can take, for instance, 192.168.1.20
for your PC.
Then go to the browser, and go the router`s IP address(192.168.1.1 with default settings).
You should see a very simple web page(different from the standard interface), prompting
you to upload the binary image file and upgrade.
After doing so, the modem reboots, and stands up!

Still, I think even given that I`ve tried to upgrade the modem using WiFi, that should not
cause issues by itself. I expect that the modem would firstly download the binary completely,
verify its checksum, and only then switch to it. So I can`t imagine how flaky wireless
connection would disrupt this process. I believe the issue is caused by a bug.
A support lady have also confirmed I should not have used WiFi for this purpose.
If that`s the case, then there should be some sort of warning in the management interface
before starting the upgrade, and perhaps, even a protection against usage of WiFi for the upgrade.

SJS-FCB,
так же иногда цепляет левые ДНС прошивка 1.04, причем все работает кроме web, торенты и почта нормально... ipv6 отключен. Не мог залогинется на сайтах, пока не поставил галочку в настройках межсетевого экрана фильтровать куки...